Rainwater Harvesting for Drylands and Beyond by Brad Lancaster

Curb Cuts & Curb Cores for Street-Runoff Harvesting

(with some updates, as noted below)

Curb-CUT or curb-CORE PERMIT costs:

• Permit is $45, but this can be for a whole block’s worth of curb cuts/cores, so you are incentivized to work with your neighbors. To clarify: It is $45 per permit, but you can have multiple curb cuts/cores on one permit.


• 4-inch-diameter core hole through curb. As of this writing, the minimum cost is $160 for crew to show up, but this covers the drilling of 5 core holes. If more holes are needed, the cost is $30 per hole (assuming a 6-inch-thick curb). Costs increase by $5 per inch for curbs thicker than 6 inches.
A contractor friend that cores the curb himself rents a hand-held core-drill (from Sunbelt Rental on Ft. Lowell—these drills are otherwise hard to find for rent). The rental for the whole drill set-up is $66 per day.

Interesting side note: Tucson Concrete Cutting and Coring—the coring company I recommend—says 1% of their current work is water-harvesting related.

Tucson Concrete Cutting and Coring drilling 4-inch hole through curb. Drill is attached to hose to wet cut and reduce wear on drill bit.

Tucson Concrete Cutting and Coring drilling 4-inch hole through curb. Drill is attached to hose to wet cut and reduce wear on drill bit.

Curb-CUT CUTTING costs:

• Cheapest option—for a curb up to 6 inches (15 cm) tall—is to rent a gas-powered, 14-inch (350-mm) diameter circular saw with diamond-carbide blade. This method also enables you to do a 14-inch-wide curb cut with 45º angled sides. Note that curbs taller than 6 inches (15 cm) will likely require a saw with a 20-inch (500-mm) diameter blade. Person doing the work must be very careful to make good clean, straight cuts. To make the horizontal cut, the basin inlet must be dug before the cut is made, so saw can cut along the dirt-side of the curb at the elevation of the bottom of the curb-side street gutter. Once all cuts are made and the cut-out section of curb is removed, the remaining curb and the cut areas must be ground smooth with a grinder.

Note 1: Larger/taller curbs may require a larger saw with a 20-inch (500-mm) diameter blade, but this saw is much heavier, more difficult to use, and more dangerous to use than a 14-inch saw. So operator must be strong and very careful.
Note 2: This DIY approach is not currently legal in Tucson, where you are required to hire a contractor to do the cutting of the curb—see below for those prices.
Note 3: This DIY approach is legal in other communities (check with your local authorities).

Legal (in Tucson) options:

• Custom Saw Cuts in Tucson charges $300 for one 2-foot curb cut with “wings” (as of January 2017). This price drops as you do more cuts so plan ahead and team up with your neighbors to save money and increase stormwater harvesting on your block. If you are doing two 2-foot curb cuts, the price is $450, or $225 per cut. From there, the price goes up by $100 for each additional curb cut at the same location. (So three curb cuts at one location would be $550, or $183.33 per cut. Four curb cuts at one location would be $650, or $162.50 per cut.) Once all cuts are made and the cut-out section of curb is removed, the remaining curb and the cut areas are ground smooth with a grinder. The equipment used by Custom Saw Cuts makes longer-sloping wings angled less than 45º (the saw cannot cut as steep as 45º). Depending on the height of the curb, the wings will be 2–4″ longer than they would be if the angle were 45º.

Note that contractors who do the cut with a 14″ circular saw can charge much less because they don’t need the very expensive horizontal-curb-cutting machine. Tucson Concrete Cutting and Coring has the equipment to do this; call them for an estimate.

Interesting side note: Custom Saw Cuts—Tucson’s horizontal-curb-cut contractor—says 7-10% of their work is water-harvesting related.

Gas-powered circular saws: 14-inch diameter blade on left, 20-inch diameter blade on right. Equipment owned by Tucson Concrete Cutting and Coring.

Gas-powered circular saws: 14-inch diameter blade on left, 20-inch diameter blade on right. Equipment owned by Tucson Concrete Cutting and Coring.

Curb-cut/core-BASIN-DIGGING costs:

• Free if you and neighbors do the digging by hand (just make sure you first call Blue Stake—a free service marking underground utilities—to make sure you are not digging where there are underground utilities).

• If you are hiring a backhoe operator (I recommend Little John Excavating in Tucson) to dig your basins (each basin being 4 feet wide, 4–6 feet long, and 12–18 inches deep), the cost is about $60–$100 per basin to dig basin and remove the soil dug out. (Note that this is assuming 10–12 basins are being dug; if fewer basins, the per-basin cost increases. Minimum charge for operator to show up and dig a basin (without removing soil) is $160 to $300—check with operator.)

Interesting side note: The backhoe operator I recommend—John Litzel of Little John Excavating—says 40–60% of his work is water-harvesting related.

Curb-cut/core-BASIN ROCK costs:

If you need to rock the banks/sides of the basins (if slopes are gradual, rock may not be needed, but in small urban spaces we typically need steeper banks and thus rock to stabilize and delineate basin banks) the cost is as follows:

• Free-ish if you salvage the rock or broken-up concrete chunks (a.k.a., urbanite, from sources such as broken-up sidewalks). You just need to pay for fuel for the vehicle to move the material.

• $30 per yard of Catalina granite rock, 8–20-inch in diameter from rock supplier (e.g., Churchman Sand and Gravel). Two yards is typical minimum amount of rock for a basin 4 feet wide and 4–6 feet long. (Deeper basins will need more rock. Ordering a full truckload often results in free delivery.)

Curb-cut/core-BASIN-PLANTING costs:

• Free if you grow out your own plants. A neighbor, Sky Jacobs, does this in our neighborhood. Or you can plant seed directly in basin. I’ve had 80–90% success-rate doing just that when I plant seed with the rains in the rainy season. Note: Some seed needs to be scarified (methods include nicking the seed coat with nail clippers before planting)—check with local growers for tips.

• $8–$25 per 5-gallon tree if you get from city tree program (Trees for Tucson) or a local nursery.

See here for recommended trees and here for more info on those and other plants for southern Arizona.

Curb-cut/core-BASIN-MULCHING costs:

• Free if you pick up mulch/wood chips from a local firewood distributor, if you cut up your own on-site prunings into mulch, or if you get a local tree-trimming company (e.g., Romero Tree Service) to give you their chipped-up prunings (cheaper for them than to take “waste” to dump).

• If you want to buy mulch in Tucson, you can get high-quality screened mulch from Fairfax Companies (3-inch decorative mulch is the best, as smaller material decomposes more quickly, and can more easily float away). Fairfax turns local green “waste” into mulch. Delivery cost is the same for a full or partial truckload, so collaborate with neighbors and get a full truckload delivered.


(return to top)


Concrete Coring Company
(602) 268-1439

Southwest Curb Cut
Ernie Hey
(602) 550-4085


Custom Saw Cuts
(520) 624-2191

Tucson Concrete Cutting and Coring
Glenn Van Houten
(520) 747-7364


(return to top)

This site is a comprehensive information center for efficiency, rainwater, graywater, stormwater and black water management, capture and reuse.  You can find Products and Services from around the state and country, links to Rebates and Incentives, a Calendar of statewide water events, Tips, Best Practices, Demonstration Projects, Films, Blogs, an Art Gallery, and much more.

Los Angeles

La Loma Development

Fast Forward Concrete Cutting

New Mexico

(return to top)

Santa Fe

Raincatcher, Inc.
They do curb cuts

Rhonda Concrete Cutting
(505) 474-3612
They do curb cores

Silver City

Stream Dynamics, Inc.


Drops in a Bucket Blog

 »Read all blog posts...

Sign up for the Newsletter

Upcoming Events

  1. Desert Green XXV

    September 30 - October 1
  2. 2021 Rocky Mountain Natural Building Conference

    October 14 - October 16
  3. Water Harvesting Design Certification: Fall 2021

    November 8 - November 20
  4. Water Harvesting Design Certification: Spring 2020

    February 28, 2022 - March 12, 2022

Umbrella Newsletter

The Umbrella: Summer 2020

THE UMBRELLA: A catch-all of resources, events, media, and more from Brad Lancaster In this time of Covid-19 and spending more time at home to be safe, I’ve been grateful for the solace, inspiration, and bountiful sustenance my water-harvesting gardens, landscape, and neighborhood forest has provided me, my family, friends, and neighbors. Record summer heat […]

 »Read all newsletters...

Like what this website offers?

Donations are greatly appreciated as they enable us to continuously update this expansive resource and generate new content. Thanks!